The first flush
With fancy computer equipment comes annoying computer maintenance. Today has been a challenge! Thankfully finished, mostly. It’s been roughly six months since I took the plunge and built my own custom watercooling loop for my computer. Since today is the first flush, I figure I can tell the story and talk about how it went. Spoiler, it went both better and worse than I expected.(more…)
I’ve quickly come to regret purchasing my new(ish) fancy laptop. I get complements on it because it looks impressive and if it worked correctly it would be very impressive. The problem is that it has been causing me headaches since I bought it. Technically this is the second one, the first one was replaced and the second had the same exact issues. So instead of exchanging it again and going through that whole mess, I decided to crack it open and do the fixing myself.(more…)
A beginners guide to watercooling, from a beginner.
I have built a lot of computers over the years. It’s actually not that hard to do since most things are labeled and use different types of connectors so it’s hard to screw it up unless you’re not paying attention. Up until recently I’ve never watercooled a PC, at least not in the build it myself sense. The internet is full of how-to guides to help you do this, but most of them are from people who do these types of builds regularly. I find that they skip over some of the basic things that you may need to know because they’ve forgotten that it’s not common knowledge. Since I’ve successfully finished my first build and don’t like hoarding knowledge, I want to share how to do it, for beginners, by a beginner.(more…)
PC build part eight, closing the loop
As promised this is the grand finale to the custom water cooling hard tube build saga. As in, the computer is back up and running… finally. It’s been a journey, but I’m hopeful that the latest mods will keep me from having any more problems that I need to stop my work and fix. I mean modding your computer for fun is one thing, needing to do it is a whole other thing. Still, I’m thankful for the little pause and I got to make a few needed changes/upgrades while the computer was down so it isn’t all that terrible.(more…)
PC build part seven, the tale of the leaky loop
Well I’ve done it… mostly. The loop is finally complete and I’ve pressure test it. There were of course some technical difficulties, which I resolved, but I also caused because I’m an idiot. I wasn’t planning on making another computer post until I had the thing turned on and finished, but today I want to tell the story of how a $20 USD part saved my computer.(more…)
PC build part six, now with more bends!
Yep, still working on the hard tube bends. It’s a lot… harder than it looks! Pun fully intended. Today I have good news and bad news. The bad news is there’s still some work to be done before I get to pressure test and finally finish this build. The good news is there’s only one bend I need to make and one or two I would like to redo if I have enough tubing for it.(more…)
PC build part five, the first bends
We’re getting bendy! After all the work I had to do yesterday I didn’t think there would be time to bend tubing yesterday, but I was determined to get started and I did. The good news, some of it’s done. The bad news, bending tube isn’t easy. There was a lot of trial and error, even more waste, and even now it’s not perfect *sad face* … but it’s almost time to wrap this project up!(more…)
PC build part four, electrical fire edition!
Okay, okay clickbait headline, I admit it. If you’re here for a real electrical fire you’re out of luck. Thankfully I haven’t had an electrical fire… yet, I haven’t turned the computer on since I’ve started this project. However, a few things happened yesterday so I need to figure out my cable management before I get too much further. It’s something I’ve been ignoring and I’m finally sharing some of the mess that I’ve (somewhat purposefully) been hiding.(more…)
Part three, extreme PC modding!
It’s no secret, it’s been a hell of a week for me. To help distract me (unsuccessfully) I decided to do some of the major mods to the PC that needed to happen in order to get everything the way I want it for the final assembly. I’m hoping tomorrow will be that day, but there are still (STILL) parts I’m waiting on, so it may be a photo finish. If not, well I can always finish is during the week or next weekend (probably).(more…)
Day two, the computer teardown
Well it’s day two of the big computer watercooling loop install and I’m already running into several problems. Some of them can be fixed quickly, while others… let’s just say I needed to get different parts so I’m in the process of doing that. As promised, there are tons of photos and explanations of everything I’ve done so far and why this is turning into a headache. Sometimes doing a custom job means getting extra custom.(more…)
Day one of the computer rebuild
Well today’s the day I crack open the computer case and get to work on fixing my desktop computer. Since I have not popped anything open yet, I want to talk a bit more about the plan going in, how I am going to do things, why you should do it too if that kind of thing sounds fun to you, and why I selected some of the things I did.(more…)
The computer rebuild plan
Okay after yesterday’s news that my computer is once again limping along I spent the day trying to figure out what to do. After spending a ludicrous amount of time researching and finding the parts I want to replace the clogged garbage I’m currently dealing with I think I have it all figured out, but it’s not going to be an easy (or cheap) fix. The good news is this is going to be the ultimate solution, the one that will (hopefully) be the last fix until either something breaks, I rebuild the computer completely, or I graduate.(more…)
Well if it isn’t the consequences of my own actions. Or maybe not, maybe I’m just unlucky. I am once again having desktop computer troubles. It’s the return of the heat issue, thankfully this time I caught it somewhat early (I think). Since this seems to be a reoccurring issue I think we’ll try to fix it with a slightly more permanent solution. The problem? The cost, this couldn’t have happened at a worse time, but not all is lost, at least not yet.(more…)
Okay, lots of work and not a lot of time to do it in, but today I thought I would show off the internals of my computer since I had to swap out the watercooler for one that wasn’t garbage. This is a follow up to this post, so with the background out of the way, let’s go!(more…)
I had a feeling this may happen, I just didn’t expect it to happen when I was so against the wire to get this project done. I’m having computer troubles. Not my laptop thankfully, but my desktop computer is feeling a little… warm. I’ll explain and then get into what I’m doing to fix it, so today let’s talk about my computer!(more…)
Day 129: Everything is breaking!!!
Well it’s post Christmas day and I have to say my stealth wrapping was a hit. Of course, after the first gift (or even the second gift) people catch on, but overall it was a lot of fun and I even got a few apologies for some of the ill will based on my apparent lack of wrapping abilities. I HIGHLY recommend giving it a shot. So let’s talk about the image above for a minute.